Ukrainietiška kosmetika
+ Reply to Thread
Rodyti rezultatus nuo 1 iki 21 iš 21

Tema: Dėl DRX 9255

  1. #1
    Fuksas silis is an unknown quantity at this point
    Registracijos data
    Jul 2006
    Žinučių
    1
    Rep Power
    0

    Pagal nutylėjimą Dėl DRX 9255

    Sveiki. gal padėtumėt susigaudyti kuris modelis skirtas europos rinkai ir ar išvis toks yra( ta prasme kad radija grotu visais dažniais). Pasimečiau tarp tu modelių HX-D1, HX-D2(čia lygtai naujasnis modelis), Adzest 9255. Ąčiū už pagalbą.

  2. #2
    Savas ZaXaS is an unknown quantity at this point ZaXaS's Avatar
    Registracijos data
    Feb 2007
    Vieta
    Vilnius-Siauliai
    Žinučių
    539
    Rep Power
    0

    Pagal nutylėjimą

    Citata silis rašė čia: Peržiūrėti žinutes
    Sveiki. gal padėtumėt susigaudyti kuris modelis skirtas europos rinkai ir ar išvis toks yra( ta prasme kad radija grotu visais dažniais). Pasimečiau tarp tu modelių HX-D1, HX-D2(čia lygtai naujasnis modelis), Adzest 9255. Ąčiū už pagalbą.
    HX Europiniai

  3. #3
    Blokuotas už kloną eXtreme is on a distinguished road eXtreme is on a distinguished road
    Registracijos data
    May 2005
    Vieta
    Kaunas
    Amžius
    44
    Žinučių
    379
    Rep Power
    0

    Pagal nutylėjimą

    HX-D2 tik
    HX-D1 kiek zinau buo leistas tik Japonu rinkai.

  4. #4
    Savas ZaXaS is an unknown quantity at this point ZaXaS's Avatar
    Registracijos data
    Feb 2007
    Vieta
    Vilnius-Siauliai
    Žinučių
    539
    Rep Power
    0

    Pagal nutylėjimą

    Citata eXtreme rašė čia: Peržiūrėti žinutes
    HX-D2 tik
    HX-D1 kiek zinau buo leistas tik Japonu rinkai.
    Nesiginčysiu

    Sorry už dezinformaciją

  5. #5
    Aktyvus okx is on a distinguished road okx is on a distinguished road
    Registracijos data
    Aug 2009
    Vieta
    Vilnius
    Amžius
    40
    Žinučių
    109
    Rep Power
    16

    Pagal nutylėjimą

    Nekuriant naujos temos,
    Kiek pastebėjau 9255 pagal specifikacijas turi visus reikiamus išėjimus, t.y. priekis/galas/subas
    http://www.clarion.com/us/en/product...294764151.html

    Bet kiek pastebėjau is foto pardavinėjamų variantų e-bay, tai išėjimai buna tik priekis/galas.
    Klausymas: ar tiesiog nedažiurėjau foto (kreivai nufotkinta) ar visgi jų buvo kelios modifikacijos ?

  6. #6
    Ekspertas omsonass will become famous soon enough omsonass will become famous soon enough omsonass will become famous soon enough omsonass will become famous soon enough omsonass's Avatar
    Registracijos data
    Sep 2008
    Vieta
    vilkaviskis
    Amžius
    40
    Žinučių
    1,800
    Rep Power
    34

    Pagal nutylėjimą

    Citata okx rašė čia: Peržiūrėti žinutes
    Nekuriant naujos temos,
    Kiek pastebėjau 9255 pagal specifikacijas turi visus reikiamus išėjimus, t.y. priekis/galas/subas
    http://www.clarion.com/us/en/product...294764151.html

    Bet kiek pastebėjau is foto pardavinėjamų variantų e-bay, tai išėjimai buna tik priekis/galas.
    Klausymas: ar tiesiog nedažiurėjau foto (kreivai nufotkinta) ar visgi jų buvo kelios modifikacijos ?
    kažką negerai nužiūrėjai, tavo linke juk matosi, kad 4 poros išėjimų ir dvi poros su įėjimais

  7. #7
    Savas Mindaugas is on a distinguished road Mindaugas is on a distinguished road Mindaugas's Avatar
    Registracijos data
    Oct 2003
    Vieta
    Bergen, Norway
    Amžius
    54
    Žinučių
    538
    Rep Power
    26

    Pagal nutylėjimą

    tai gal tu maisai DRZ ir DRX? DRX turi tik du isejimus.
    *Šiame poste išsakyta autoriaus nuomonė dažniausiai nesutampa su skaitytojo nuomone.
    ---------------
    tel. +47 46 222090
    info@caraudio.lt
    www.caraudio.lt

  8. #8
    Ekspertas omsonass will become famous soon enough omsonass will become famous soon enough omsonass will become famous soon enough omsonass will become famous soon enough omsonass's Avatar
    Registracijos data
    Sep 2008
    Vieta
    vilkaviskis
    Amžius
    40
    Žinučių
    1,800
    Rep Power
    34

    Pagal nutylėjimą

    Citata Mindaugas rašė čia: Peržiūrėti žinutes
    tai gal tu maisai DRZ ir DRX? DRX turi tik du isejimus.
    Clarion DRX9255 turi dvi poras rca


  9. #9
    Savas Mindaugas is on a distinguished road Mindaugas is on a distinguished road Mindaugas's Avatar
    Registracijos data
    Oct 2003
    Vieta
    Bergen, Norway
    Amžius
    54
    Žinučių
    538
    Rep Power
    26

    Pagal nutylėjimą

    To omsonass. Ačių, kad išvertei i LT kalbą
    *Šiame poste išsakyta autoriaus nuomonė dažniausiai nesutampa su skaitytojo nuomone.
    ---------------
    tel. +47 46 222090
    info@caraudio.lt
    www.caraudio.lt

  10. #10
    Aktyvus Ricka is on a distinguished road
    Registracijos data
    Aug 2010
    Amžius
    36
    Žinučių
    237
    Rep Power
    16

    Pagal nutylėjimą

    na, ar dar yra kasnors, kas perstumineja dažnius drx'ui?
    Drx 9255 ; scanspeak d3804, rs audio spl --> audiosystem twister f4 260; jl audio 10w3v3 --> U-Dimension u-pro 1k.1xd|

  11. #11
    Blokuotas Inproof can only hope to improve Inproof can only hope to improve
    Registracijos data
    Jan 2011
    Amžius
    33
    Žinučių
    961
    Rep Power
    0

    Pagal nutylėjimą

    Čia ne, rašyk pm nukreipsiu tinkama linkme.

  12. #12
    Ekspertas darializ will become famous soon enough darializ will become famous soon enough darializ will become famous soon enough darializ will become famous soon enough darializ's Avatar
    Registracijos data
    Oct 2006
    Amžius
    40
    Žinučių
    739
    Rep Power
    25

    Pagal nutylėjimą

    Citata Ricka rašė čia: Peržiūrėti žinutes
    na, ar dar yra kasnors, kas perstumineja dažnius drx'ui?
    esu girdėjęs, kad ten nieko nereikia lituoti. pasiskaitinėk užsienio forumuose. kogero ten bus nustatymuose, arba koki "switcha" perkelt.
    u-dimension 40xs, u-dimension 20vs

  13. #13
    Blokuotas Inproof can only hope to improve Inproof can only hope to improve
    Registracijos data
    Jan 2011
    Amžius
    33
    Žinučių
    961
    Rep Power
    0

    Pagal nutylėjimą

    Keičiasi tik ant clarion DRX9255. Addzest EX EXL ir kitom blatnesnėm versijom nesikeičia, reikia lituoklio pagalbos kiek žinau.

  14. #14
    Ekspertas darializ will become famous soon enough darializ will become famous soon enough darializ will become famous soon enough darializ will become famous soon enough darializ's Avatar
    Registracijos data
    Oct 2006
    Amžius
    40
    Žinučių
    739
    Rep Power
    25

    Pagal nutylėjimą

    Citata Inproof rašė čia: Peržiūrėti žinutes
    Keičiasi tik ant clarion DRX9255. Addzest EX EXL ir kitom blatnesnėm versijom nesikeičia, reikia lituoklio pagalbos kiek žinau.
    gali būti, nesiginčysiu. bet siūlyčiau pasidomėti. gali likti nustebęs kaip paprasta praplėsti.
    u-dimension 40xs, u-dimension 20vs

  15. #15
    Blokuotas Inproof can only hope to improve Inproof can only hope to improve
    Registracijos data
    Jan 2011
    Amžius
    33
    Žinučių
    961
    Rep Power
    0

    Pagal nutylėjimą

    Nėra čia ką domėtis. Reikia spausti BAND ir du kart į kairę arba į dešinę, tai galioja visiems berots, bet jei yra addzest tai jis keičia ten japaškų regionams tik. Jei us/uk versijos tada įmanoma su knopkėm. O kaip su lituokliu elgtis tai dar neteko užmatyti. Jeigu kas žinot kur aprašyta tai prašau pasidalint.

  16. #16
    Blokuotas Inproof can only hope to improve Inproof can only hope to improve
    Registracijos data
    Jan 2011
    Amžius
    33
    Žinučių
    961
    Rep Power
    0

    Pagal nutylėjimą

    Ok trupučiuką pasiskaičiau ir radau visą eiga kaip tai reikia padaryti.

    http://www.diymobileaudio.com/forum/...255-tuner.html

    Toli gražu nepaprasta

    versta iš rusų kalbos.

    Here is the article is like a man tinkering with the radio:

    That allowance, on which I remade, because there is clearly written that can be distributed freely on the territory of Russia, etc. publish the name of the author, but my amendment, which was skated on the 2 copies DRH9255, so that they consider the regularity and advise you to use!
    Inaccuracies in the article, and add / correct a signed text of the valves, so you must first COMPLETELY Read the full article, get to the core and get down to business!

    As I rewrote the tuner in the DRX9255. Reporting manual.

    (C) Docent 3D
    Andrew, Peter


    The following information is a summary of my research on "Remaking FM-tuner Addzest DRX9255 on the European frequency range," and allowed to free spread throughout Russia, CIS countries, as well as Europe, America and others ....


    To start a small introduction. The basis for the alteration of operations was the information kindly provided by Alexander Yureninym (Alex), as well as material from the book by Anatoly Shishatova (ZHSH) "at the Concert Hall koloesah." Ea is a special thank you to them.

    A bit of theory to help understand the process of remaking. FM tuner with DRX9255 built under the scheme with the local oscillator and frequency synthesizer. The idea of ??this design is that the LO signal is divided by frequency and compared with the reference signal frequency and phase. The reference signal is generated separately, in the management of the scheme and the step is in the relevant frequency range. In our case it is 0.05 MHz. After comparison, the control signal is generated LO frequency, which changes the latter so that it was equal to the net step frequencies multiplied by a factor of division. Thus, fine tuning is achieved to the desired frequency oscillator. LO frequency control, and other tunable LC-circuits arranged with varicaps included in this circuit.

    Now, how and what was done, and how can you do if you decide to rework.

    The stage of disassembly.
    - Take out Addzest RDX9255 of the car.
    - Remove the top cover.
    - Remove the bottom cover.
    - Remove the front panel.
    - Turn off and remove the vehicles.
    - Turn off and put off to the side of her hair off RCA-plugs.
    - Unscrew all the screws that hold the rear wall of the housing unit with everything else.
    - Unsolder the wall from the board (two points) and remove it.
    - Carefully remove the lid-screen tuner. It is attached to the snap-ledges. Two left and right.

    Stage alteration management system
    - Put the unit upside down and "face" of his own. In the upper right corner of the board we find two pairs of pads, next to which it is written «Japan» and «USA». SMD-resistor is zero resistance to solder a pair of contacts «Japan» a couple of «USA». Everything. Now, the control system switched to the Euro-American bands. This means that the display will reflect the figures familiar to us from 87.5 to 108MHz, and the frequency synthesizer is to compare the frequency of oscillator, taking into account the fact that the oscillator has been tuned to other frequencies (for our range).

    - To change the pitch of the tuner of American 200kHz to 50kHz for our holding down the «BAND» double-click on the "<<"

    - Switch to manual / automatic setting by pressing and holding the button «BAND»

    Stage of alteration itself tuner.
    - If you look at the back of the unit, we will see a lot of on-board tuner coils and other detalyushek Lilliputian size. As it is not terrible, but some of them we have to vypayat and subjected to modification. To do this, always need a low-power (preferably not on the 220, but with the step-down transformer), a small soldering iron, a magnifying glass and good light source.
    - So, we place the device flat on the main board down. We are looking at him from behind. Standing vertically on board tuner, we are interested in three coils (TOP - BLACK, WHITE MEDIUM, LOWER GREEN BEZKARKASNAYA (looks like a very large, spiral).
    They are strictly on a vertical axis passing through the center of the board tuner. The first coil on top - odnoobmotochnaya. This oscillator circuit coil. Under it a trimmer toli, toli trimmer capacitor - to us he was not interested. Another double-wound coil is below - it's interstage transformer with tunable LC-circuit at one of its windings. Still lower is a frameless coil of the input circuit of the tunable radio frequency FM tuner.

    Alteration of LO.
    - Put a muzzle device in place and turn it. In Tuner mode are connecting a voltmeter to the 15th pin connector tuner, designated VT. According to it, the tuner receives the signal tuning circuits with a frequency synthesizer circuit. Regardless of the selected frequency in this output will be about 7volt. Though when all is well, there must be a minimum of 2.1 (87.5 MHz) to 6Volt (108MHz). But we switched to a different synth mode, and the oscillator is still running in the old format and can not be reconstructed. Accordingly, the frequency synthesizer provides the best possible control signal to the LC-circuits varicaps tuner. In order to outline the LO can be reconstructed at high frequencies, it is necessary to reduce the inductance of the coil. Fed to it. It turns 4.5. Wind off one or two turns (do not cut off the excess wire!!!) And solder the coil on the back of the card. So convenient to adjust. In the tuner is turned expose the frequency of 87.50 MHz and a control voltage at the VT. It should be 2.1 V. If you close, you can try a miniature ferrite rod otvertochkoy twist in the coil and adjust the voltage of 2.1 V. If the voltage is always greater than necessary, it is necessary to further reduce the number of turns in the coil. If the voltage at the point of VT markedly less than 2.1 volts, you overdid it and you want to turn back into place. I have the grace came when I removed about a half turn (unfortunately tuning inductance with the ferrite core has a very small range of adjustment). When you tune into the very same 2.1 V, then try to go to 108MHz. At the point of VT should be about 6Volt. I was a little less by the way, but it is IMHO not a crime. Now you can finally cut off the excess wire and solder the coil in its place. Radio has already PLAY. Bad, but it should!
    So, in practice, turned the voltage at the point at 87.5 MHz, VT 3 volts!, ??With the core of the Black coil should be in the middle position and have the freedom to adjust!!
    More to break and remake does not have to!!!
    Crank radio, first known to be a good tune on the wave, take a mini otvertochku, such as for hours, and begin to customize the second coil (which is white), twisting back and forth achieve the best result, and then adjusts the first coil (black, although a full chocolate I had a at 3 volts! at the point of VT) and least adjusts the last coil (green) by gentle moving apart / moving the turns and get pleasure from the work done!
    Unfortunately, pictures do not, disassemble the new no mood and time, if someone does not understand - please send photos of the tuner-tknu what and where to do it!
    Reconfiguring the remaining circuits.
    - It is necessary to reconfigure the input LC-circuit. Fed to the appropriate coil and remove one turn. Solder back. The reception quality must now be considerably higher. Moving / pushing the turns of the circuit configuration can be changed and therefore the quality of reception. In fact, the input circuit is a bandpass filter with all the considerations and consequences.

    -Next. Tune in a station manually with the naiotvratitelneyshim reception. And start to turn the ferrite rod coil-winding. According to the ideology of the reception should be improved by reducing the effect of iron on the winding. Yes there seems, in practice, the way it is! I do my best result was achieved with a fully torn off from the coil core. With this experience with the removal of a single turn coil which is built LC-circuit was not very successful. The inductance of the coil was too small and even a ferrite rod was not able to raise it to the required level. While this may be a feature of a particular instance and no more. In any case, I will describe how and what to do. In this case we are interested in is the winding, which is connected to the board with two pins varicap (This is a three-legged SMD-bony plates on the back side of the board). I have been a top coil on coil and its conclusions have been soldered to the board of the oscillator coil. Fed to the coil and the wind off a round with that winding. Then solder it back and donastraivaem ferrite rod ..

    - Putting it all in reverse order, and .........
    ....... listen to the radio in the usual range

  17. #17
    Aktyvus Ricka is on a distinguished road
    Registracijos data
    Aug 2010
    Amžius
    36
    Žinučių
    237
    Rep Power
    16

    Pagal nutylėjimą

    taip pat ir rusu kalba
    Вот статейка как человек переделывал радио :

    Вот пособие, по которому я переделывал, так как там ясно написано, что можно бесплатно распространять на территории России и т.д. публикую от имени автора, а вот мои поправки, которые были откатаны на 2-х экземплярах ДРХ9255, так что их считаю закономерностью и советую использовать!
    Неточности в статье и дополнения/исправления помечу краным текстом, так что СНАЧАЛА НЕОБХОДИМО ПРОЧИТАТЬ ВСЮ СТАТЬЮ ПОЛНОСТЬЮ, ВНИКНУТЬ В СУТЬ И ПЕРЕХОДИТЬ К ДЕЛУ!!!

    Как я переделывал тюнер в DRX9255. Отчет-пособие.

    (C)Docent 3D
    Андрей, Питер


    Нижеследующая информация представляет собой итог моих изысканий по теме "Переделка FM-тюнера Addzest DRX9255 на Европейский диапазон частот" и допускается к бесплатному распространению на всей территории России, стран СНГ, а также Европы, Америки и прочих....


    Для начала маленькое введение. Основой для проведения операций по переделке явилась информация, любезно предоставленная Александром Юрениным (Alex), а так же материалы из книги Анатолия Шишатова (ЖШ) «Концертный зал на колоесах». Эа это им отдельное спасибо.

    Немного теории для облегчения понимания процесса переделки. ФМ-тюнер у DRX9255 построен по схеме с гетеродином и синтезатором частот. Идея такой конструкции в том, что сигнал гетеродина делится по частоте и сравнивается с опорным сигналом по частоте и фазе. Опорный сигнал вырабатывается отдельно, в управляющей части схемы и равен шагу частот в соответствующем диапазоне. В нашем случае это 0,05МГц. После сравнения, вырабатывается сигнал управления частотой гетеродина, который изменяет последнюю так, чтобы она была равна шагу сетки частот умноженному на коэффициент деления. Таким образом достигается точная настройка гетеродина на необходимую частоту. Управление частотой гетеродина, а также другими перестраиваемыми LC-контурами организовано с помощью варикапов, включенных в эти контура.

    Теперь о том, как и что было сделано, и как можете сделать вы, если решитесь на переделку.

    Стадия разборки.
    - Вынимаем Аддзест RDX9255 из машины.
    - Снимаем верхнюю крышку.
    - Снимаем нижнюю крышку.
    - Снимаем переднюю панель.
    - Откручиваем и вынимаем транспорт.
    - Отключаем и откладываем в сторону косу выходных RCA-разъемов.
    - Откручиваем все винты, которые скрепляют заднюю стенку корпуса аппарат со всем остальным.
    - Отпаиваем стенку от платы (две точки) и снимаем ее.
    - Аккуратно снимаем крышку-экран тюнера. Она крепится на защелках-выступах. По две слева и справа.

    Стадия переделки системы управления
    - Кладем аппарат вверх дном и «мордой» от себя. В правом верхнем углу платы находим две пары контактных площадок, рядом с которыми написано «Japan» и «USA». SMD-резистор нулевого сопротивления перепаиваем с пары контактов «Japan» на пару «USA». Все. Теперь система управления перешла на европейско-американский диапазон частот. Это означает, что на дисплее будут отражаться привычные нам цифры от 87,5 до 108МГц, а синтезатор частот будет сравнивать частоту гетеродина с учетом того, что настраиваться гетеродин должен уже на другие частоты (для нашего диапазона).

    - для изменения шага настройки тюнера с американских 200КГц на наши 50КГц необходимо удерживая клавишу «BAND» дважды нажать на клавишу «<<»

    - переключение ручная / автоматическая настройка осуществляется нажатием и удержанием клавиши «BAND»

    Стадия переделки собственно тюнера.
    - Если смотреть на аппарат с задней стороны, то мы увидим на плате тюнера кучу катушек и прочих деталюшек лилипутского размера. Как это не ужасно, но некоторые из них нам придется выпаять и подвергнуть модификации. Для этого обязательно нужен маломощный (желательно не на 220В, а с понижающим трансформатором) паяльник с тонким жалом, увеличительное стекло и хороший источник света.
    - Итак, кладем аппарат плашмя, основной платой вниз. Мы смотрим на него с тыла. На вертикально стоящей плате тюнера нас будут интересовать три катушки (ВЕРХНЯЯ - ЧЕРНАЯ,СРЕДНЯЯ БЕЛАЯ, НИЖНЯЯ ЗЕЛЕНАЯ БЕЗКАРКАСНАЯ(похожа на довольно крупную, спираль).
    Они расположены строго по вертикальной оси, проходящей по центру платы тюнера. Первая катушка сверху – однообмоточная. Это катушка контура гетеродина. Под ней какой-то толи подстроечный резистор, толи подстроечный конденсатор – нам он неинтересен. Еще ниже двухобмоточная катушка – это межкаскадный трансформатор с перестраиваемым LC-контуром на одной из его обмоток. Еще ниже находится бескаркасная катушка входного перестраиваемого контура радиочастоты ФМ-тюнера.

    Переделка гетеродина.
    - Ставим морду аппарата на место и включаем его. В режиме тюнера подключаемся вольтметром к 15-му контакту разъема тюнера, обозначенному VT. По нему на тюнер поступает сигнал перестройки контуров со схемы синтезатора частот. Вне зависимости от выбранной частоты на этом выходе будет около 7вольт. Хотя когда все хорошо, там должно быть от 2,1(87,5МГц) до 6Вольт (108МГц). Но мы ведь переключили синтезатор в другой режим работы, а гетеродин пока еще работает в старом формате и не может перестроиться. Соответственно синтезатор частот дает максимально возможный управляющий сигнал на варикапы LC-контуров тюнера. Для того, чтобы контур гетеродина мог перестраиваться на бОльшую частоту, нужно уменьшить индуктивность его катушки. Выпаиваем ее. На ней 4,5 витка. Отматываем один-два витка (при этом не отрезая излишек провода!!!!!!!!!) и припаиваем катушку с обратной стороны платы. Так удобно для настройки. На включенном тюнере выставляем частоту 87,50МГц и контролируем напряжение в точке VT. Должно быть 2,1В. Если близко, то можно попробовать миниатюрной отверточкой покрутить ферритовый стерженек в катушке и отрегулировать напряжение на 2,1В. Если напряжение все время больше чем нужно, то необходимо еще уменьшить количество витков в катушке. Если напряжение в точке VT заметно меньше 2,1Вольт, то вы перестарались и нужно вернуть виток на место. У меня благодать наступила тогда, когда я удалил примерно полтора витка (к сожалению подстройка индуктивности с помощью ферритового сердечника имеет очень малый диапазон регулировки). Когда вы настроитесь на те самые 2,1В, то попробуйте перейти на 108МГц. В точке VT должно быть около 6Вольт. У меня было чуть меньше кстати, но это ИМХО не криминал. Теперь можно окончательно обрезать излишек провода и впаять катушку на ее место. Радио должно уже ИГРАТЬ. Плохо, но должно!!!
    Итак, на практике получилось напряжение в точку VT при 87,5Мгц 3 Вольта!, при этом сердечник Черной катушки должен находиться в среднем положении и иметь свободу регулировки!!!!
    Больше ломать и переделывать ничего не нужно!!!!!!!
    Врубаем радио, сначала настраиваемся на заведомо хорошую волну, берем мини отверточку, типа для часов, и начинаем настраивать вторую катушку(которая белая), крутя туда-сюда добиваемся наилучшего результата, после чего подстраиваем первую катушку(черную, хотя полный шоколад у меня был при 3 вольтах! на точке VT) и в последнюю очередь подстраиваем последнюю катушку(зеленую) методом аккуратного раздвигания/сдвигания витков и получаем удовольствие от проделанной работы!!!
    К сожалению фоток не делал, разбирать по новой нет никакого настроения и времени, если кто совсем не понял - шлите фото тюнера- ткну чего и где делать!
    Перенастройка остальных контуров.
    - Необходимо перенастроить входной LC-контур. Выпаиваем соответствующую катушку и удаляем один виток. Впаиваем обратно. Качество приема должно теперь быть существенно выше. Сдвигая / раздвигая витки можно менять настройку контура и соответственно качество приема. По сути входной контур это полосовой фильтр со всеми вытекающими соображениями и последствиями.

    -Далее. Настраиваемся в ручном режиме на станцию с самым наиотвратительнейшим качеством приема. И начинаем крутить ферритовый стерженек двухобмоточной катушки. Судя по идеологии качество приема должно улучшаться при снижении влияния феррита на обмотку. Да что там судя, на практике так оно и есть!!! У меня у меня самый лучший результат был достигнут при полностью выкрученном из катушки стержне. При этом опыт с удалением одного витка катушки на котором построен LC-контур был не очень удачным. Индуктивность катушки стала слишком малой и даже ферритовый стержень не смог поднять ее до необходимого уровня. Хотя это может быть особенностью конкретного экземпляра и не более. На всякий случай опишу как и чего делать. В таком случае нас будет интересовать та обмотка, которая соединена на плате с двумя выводами варикапа (Это трехногий SMD-жучек на обратной стороне платы). У меня это была верхняя обмотка на катушке и ее выводы были впаяны в плату со стороны катушки гетеродина. Выпаиваем катушку и отматываем один виток с указанной обмотки. Потом впаиваем все обратно и донастраиваем ферритовым стержнем..

    - Собираем все в обратной последовательности и.........
    ....... слушаем радио в привычном диапазоне

    Надеюсь кому-то помог! С уважением Михаил
    Drx 9255 ; scanspeak d3804, rs audio spl --> audiosystem twister f4 260; jl audio 10w3v3 --> U-Dimension u-pro 1k.1xd|

  18. #18
    Aktyvus Ricka is on a distinguished road
    Registracijos data
    Aug 2010
    Amžius
    36
    Žinučių
    237
    Rep Power
    16

    Pagal nutylėjimą

    Dar klausimas, nuo kur jungti remote, yra du laidai: vienas mėlynas su balta juostele, kitas mėlynas, ant vieno itampa atsiranda tik ijungus radiją, ant kito išviso nieko nėra
    Drx 9255 ; scanspeak d3804, rs audio spl --> audiosystem twister f4 260; jl audio 10w3v3 --> U-Dimension u-pro 1k.1xd|

  19. #19
    Blokuotas Inproof can only hope to improve Inproof can only hope to improve
    Registracijos data
    Jan 2011
    Amžius
    33
    Žinučių
    961
    Rep Power
    0

    Pagal nutylėjimą

    Man atrodo pats atsakei i klausima

  20. #20
    Aktyvus Ricka is on a distinguished road
    Registracijos data
    Aug 2010
    Amžius
    36
    Žinučių
    237
    Rep Power
    16

    Pagal nutylėjimą

    Nu ir koks atsakymas, ant vieno laido yra itampa, tik ijungus radiją, tik perjungi į cd ir dingsta
    Drx 9255 ; scanspeak d3804, rs audio spl --> audiosystem twister f4 260; jl audio 10w3v3 --> U-Dimension u-pro 1k.1xd|

  21. #21
    Aktyvus Ricka is on a distinguished road
    Registracijos data
    Aug 2010
    Amžius
    36
    Žinučių
    237
    Rep Power
    16

    Pagal nutylėjimą

    gal kas turit tokį aparatą ir galit pamatuot varžą tarp korpuso ir išorinio rca kontakto?
    Drx 9255 ; scanspeak d3804, rs audio spl --> audiosystem twister f4 260; jl audio 10w3v3 --> U-Dimension u-pro 1k.1xd|

+ Reply to Thread

Bookmarks

Rašymo taisyklės

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • Jūs negalite redaguoti savo žinučių
Hostingas SERV.LT